Optishield Lux - EN

Želiš izdelek vrniti ali zamenjati?

Pri gizzmo.si omogočamo enostavna vračila, menjave ali uveljavljanje garancije. Enostavno izpolni vodnik za vračila in menjave:

Želim vračilo ali menjavo

Iščeš Garancijski list?

Garancijski list za izdelek najdeš na spodnji povezavi. Za uveljavljanje garancije sicer zadostuje samo predložitev računa.

Izjava o Skladnosti

Izjavo o skladnosti CE tega izdelka najdeš na dnu tega dokumenta.

Video

Have you ever faced the problem of finding the perfect glass for your device which has a curved display? The  Optishield Lux offers a solution in the form of a revolutionary new glass for the protection of your devices display, which offers a unique and easy installation and fastening of the glass with the help of a UV light activated adhesive liquid. With this the glass sticks to the entire surface of the screen and not just the edges, as is usual for other glasses. Perfect fit, edge to edge coverage, 100% responsiveness and perfect transparency are only some of the properties, which distinguish the Optishield Lux from other generic screen protective products.

Step 1:

  • Clean the screen thoroughly with the supplied alcohol wipe and use the regular wipe to dry it
  • Place the phone on an even surface
  • Remove and remaining dust particles
  • Remove the longer cap of the tube with the adhesive liquid and cut off the tip
  • Aim the tube over the middle of your screen, with the cut off end first
  • Slowly unscrew the longer tube cap, the adhesive will automatically get on the screen
  • Apply liquid to the center of your screen; Use the entire contents of the tube to fasten the glass
  • Remove the protective foil from the glass
  • Adjust the glass above the screen so that it will perfectly fit the phone
  • Gently lower the glass to the screen until it touches the adhesive
  • Check the alignment of the glass and the screen once again and let go of the glass
  • During the application process the glass can move slightly; adjust it gently, because excessive pressure could cause the adhesive liquid to spill over the edges of your device
  • Wait for the liquid to completely spread under the glass
  • In case the liquid spills over the edges, wipe it off immediately

Step 2:

  • If you use and external battery (Power Bank) or a charging adapter for the operation of the UV lamp, it must have an output power of at least 2A, since only then will the UV light work at full power; do not use your computer to operate the lamp
  • Use the UV light for the primary exposure of the adhesive
  • Place the turned on light above the top part of the screen for 15 seconds, then move it for 15 seconds above the bottom part of the screen, and finally over the center of the phone (the light automatically turns off after the time elapses)
  • Wipe off any excess adhesive liquid with the alcohol wipe
  • Place your phone on a flat surface and then expose the glass to UV light again
  • Expose the top part of the screen for 30 seconds first, then the lower part, and finally the middle part of the screen (total exposure time is 45 seconds for each individual part)

Removing the glass:

  • The screen of the device should face the ground, it should be turned away from you or people around you, since the glass may crack
  • Remove the glass above a trash bin
  • With your fingernail lift the glass in one of the corners and remove it slowly (sudden or too fast removal of the glass may lead to injuries)

Warnings:

  • Do not carry out installation outdoors or in direct exposure to sunlight
  • Avoid areas with lots of dust
  • The adhesive liquid is harmless, but it is not suitable for consumption
  • Impact to the glass or bending of the glass can cause it to break
  • The coating on the back of the glass prevents the tempered glass from scattering, but due to various reasons it can get damaged
  • If the glass breaks, we recommend that you remove or replace it
  • Air bubbles under glass may result from the use of an incompatible protective cover, damage caused by a fall or impact, deliberate lifting of the glass, excessive cleaning with the alcohol wipe or any other form of excessive pressure on the sides of the glass
  • If air bubbles appear during the installation they can not be removed, they may be the result of variations in the form of the device or the glass, and the installation to such a device is not recommended

The package includes:

  • 1x Premium protective glass Optishield Lux
  • 1x UV light
  • 1x Tube of adhesive liquid

Navodila za recikliranje in odlaganje


Ta oznaka pomeni, da izdelka po vsej EU ni dovoljeno odvreči med ostalegospodinjske odpadke. Za preprečevanje morebitne škode za okolje ali zdravje ljudi zaradi nenadzorovanega odlaganja odpadkov odgovorno reciklirajte in stem spodbujajte trajnostno uporabo materialnih virov. Če želite uporabljeno napravovrniti, uporabite sistem za vračilo ali kontaktirajte prodajalca, kjer ste napravo kupili. Prodajalec lahko napravo reciklira na okolju prijazen način

Izjava distributerja, da izdelek ustreza zahtevam veljavnih direktiv EU

ES – Izjava o skladnosti

VAL SKUPINA D.O.O.
HRVAŠKA 10
1000 LJUBLJANA
SI22490388

izjavljamo, da je proizvod

Optishield Lux - EN
skladen z Direktivo 2014/53/EU.

Kontakt prodajalca:

info@gizzmo.si

INFO številka

041 736 736


View this manual in other languages